Seta Oil Test Centrifuge – 6 place – 90100-0
The Seta Oil Test Centrifuge is a heated chamber centrifuge used to determine water and sediment in oils. The large diameter chamber, with six place rotor and cushioned adaptors, allows the use of 6 and 8-inch conical, pear-shaped, trace sediment and 12.5 ml tubes.
The swing-out rotor ensures that samples are held near vertical when at rest, allowing precise measurement of sediment. The centrifuge features a hinged lid that opens to the fully upright position to allow easy loading and unloading of tubes between tests.
Speed, temperature, and timing are microprocessor controlled. Run parameters are entered via a liquid-proof ‘touch panel’ and digital display.
Methods: ASTM D91, ASTM D893, ASTM D1290, ASTM D1796, ASTM D2273, ASTM D2709, ASTM D2711, ASTM D4007, ISO 3734, ISO 9030
Features
- Isothermal heaters fitted internally to the centrifuge chamber
- Temperature control using a unique algorithm to compensate for air resistance heating
- 6 place swing out rotor
- Static, near vertical bucket positioning
- Specifically designed for testing oils
- Heated chamber, ambient to 80 °C
- Pre-heat facility to ensure the bowl is at test temperature prior to the test
- Universal buckets for 12.5 ml, 6 and 8-inch glassware
- Microprocessor control with 99 memories
- Optional trolley
Precise heating for accurate results
Isothermal heaters fitted internally to the centrifuge chamber give precise temperature control to within +/-1 °C.
Fast and easy operation
9 program memories allow a user to configure the instrument to operate automatically to the specified test parameters, saving time, easing operation, and assisting repeatability. A ‘Quick Run’ mode allows short runs of up to 99 seconds.
Safety features
A motor-driven lid latch with a safety interlock prevents the centrifuge operation while the lid is unlocked. Imbalance detection and over-temperature protection protect the motor and chamber from damage.
Setafuge Hazard Reduction System
The optional Setafuge Hazard Reduction System (90010-0) can be fitted into the centrifuge to extract vapors from the chamber and significantly reduce vapor hazards.
Supplied with;
Rotor
Buckets and cushions
MAXIMUM RELATIVE CENTRIFUGAL FORCE (RCF) | 2210 g |
---|---|
MAXIMUM ROTATIONAL SPEED | 3000 rpm |
TEMPERATURE RANGE | Ambient +5 °C in the range of 20 to 80 °C (1 °C steps) |
TIMER RANGE | 10 sec to 100 hours or continuous operation |
CONTROL | Microprocessor with 99 memory capacity |
CAPACITY | 6 Samples |
VOLTAGE RANGE | 230 Vac, 50/60 Hz (Optional transformer for 110/120 V) |
POWER | 950 W |
SIZE (HXWXD) | 410 × 560 × 640 mm |
WEIGHT | 72.5 kg |
CCCN CODE | Tariff 84211970 |
Accessories, Spares, Calibration, and Training
-
Tube 8 inch x 100 ml cone-shaped (Pack of 6) – 90040-0
-
Bucket Adaptor for 90040-0 & 90060-0 (pack of 4) – 90001-2
-
Tube 6 inch x 100 ml pear-shaped (Pack of 6) – 90050-0
-
Tube 6 inch x 100 ml cone-shaped (pack of 6) – 90011-0
-
Transformer for 120 V 60 Hz Operation – 90016-0
-
High Level Centrifuge Trolley – 90015-0
-
Low Level Centrifuge Trolley – 90014-0
-
Bucket Adaptor for 90011-0 Tube (pack of 4) – 90005-2
-
Bucket Adaptor for 90050-0 (Pack of 4) – 90003-2
-
Stoppers (Pack of 50) – 90041-2
-
Centrifuge_Tube_90012-0
-
Adaptor for 90012-0 Centrifuge Tube (Pack of 4) – 90002-0
-
Setafuge Hazard Reduction System – 90010-0
-
Bottom Cushions (pack of 2) – 90000-301
-
Digital Photo Tachometer – 99960-2
-
Thermometer Digital: -199 to 199 °C UKAS Calibrated – 82012-0
-
Rotor Collet – 90000-344