Seta Coolant Module – 13870-0
Used with the Setaflash Series 3 Flash Point Tester (30000-2) and Setaflash Series 3 Plus Flash Point Tester (33000-2) for sub-ambient tests.
Note: requires dry ice.
Showing 433–448 of 641 results
-
-
Seta Cooling Unit – 22090-0
This nickel-plated brass container contains a nickel-plated copper cooling coil with one end connected to a purging valve and a pressure control valve and the other end suitable for connecting to the vessel being sampled.
-
Seta Main Chamber – 22300-3
Used to determine the vapour pressure of LPG to avoid exceeding pressure safety limits during storage, handling and use.
-
Seta Metal Cooling Block – 13880-0
For the rapid cooling of flash point tester cups between tests.
-
Seta Oxflo Controller, 6 place – 16905-3
The Seta Oxflo Controller can be used on a number of Seta instruments. It is suitable for use with non corrosive gases, and is most commonly used with air, oxygen or nitrogen.
The controller is equipped with a pressure gauge and six calibrated flowmeters. Each flowmeter is independently adjustable via a needle valve.
-
Seta Penetrometer Calibration Kit – 17150-0
Comprises set of precision ground dimension gauges which are used to verify the calibration of all Seta Penetrometers.
-
Seta Pressure Gauge – 15600-0
An oxygen safe pressure gauge with a range of 0 to 1400kPa (0 to 200psi).
For use with;
Seta Oxi-Cor Bath (15550-3)
Oxidation Vessel (15802-2) -
Seta Reid Pressure Cylinder Assembly – 180 to 700 kPa (26 to 100 psi) – 22410-0
Made from chromium-plated brass with knurled grips for safe handling and a bayonet coupling for quick leak-free connection. The volume ratio between chambers is held to close limits.
-
Seta Reid Pressure Cylinder Assembly – up to 180 kPa (26 psi) – 22400-0
Made from chromium-plated brass with knurled grips for safe handling and a bayonet coupling for quick leak-free connection. The volume ratio between chambers is held to close limits.
-
Seta Solid Sample Dispenser – 13747-0
Accurately loads solids, pastes, powders and other samples which cannot be discharged from a hypodermic syringe into flash point closed cup testers.
- Consistent sample size
- Clean, mess free operation
-
Seta Steam Calibration Kit for Steam Calibration – 12255-0
Connects to the bath jet assemblies and is supplied with a 2 litre graduated cylinder for calibrating and verifying the flow / volume of steam.
For use with the Seta Existent Gum Solid Block Bath – Steam or Air (12200-3).
-
Seta Steam Generator – 12310-3
This unit is electrically heated with a water feed pump, safety valve (preset at 1 bar), water level control and cut-out. It produces 18 kg/hr (40 lb/hr) of steam at 100 °C. Maximum working pressure is 10 bar (150 lbf/in2).
For use with the Seta Existent Gum Solid Block Bath – Steam or Air (12200-3).
-
Seta Steel Stand – 24500-0
Steel stand for use with the Distillation 500 ml flask heater (24410-5). 315 x 200 mm with 12.7 mm diameter steel rod 76 cm high.
-
Seta Wax Penetration Needle – 18490-0
Wax penetration needles for use with Seta Penetrometers. 2.5 g mass
-
SETA-CRM AvCount Verification Material – SA1006-0
The SETA-CRM AvCount Verification Material serves as a Secondary Working Standard (SWS) with a particle distribution traceable to NIST SRM 2806a and 2806d. Laboratories use it with Automatic Particle Counters (APCs) calibrated in accordance with ISO 11171 using IP 565, IP 630, and/or ASTM D7619.
This material is produced under our ISO 17034 UKAS accreditation, and is characterised in accordance with ISO 11171. Upon request, NIST 2806b values are also available.
The AvCount Verification Material is suppled in tamper-evident security packaging with full documentation, including a Safety Data Sheet (SDS). It has a two-year shelf life from the date of manufacture and comes in a 250 mL bottle.
-
SETA-CRM Cleveland Flash Point high nominal flash point 300° C (3 pack) – SETA-0412-0068
The Cleveland Flash Point Certified Reference Material is produced under our ISO 17034 UKAS accreditation and ISO 33405, it is provided with documentation compliant to ISO 33401.
The Cleveland Certified Reference Material provides a certified value for a single test method and has been characterised by an Interlaboratory Study, guaranteeing international traceability. It is a highly cost effective solution to help meet verification requirements for audited laboratories and those which comply with ISO 17025.
This hydrocarbon mixture also provides a Fire Point value (ASTM D92) and a Density measurement (ASTM D4052).
The Cleveland Reference Standard is supplied with full documentation including Safety Data Sheet (SDS), in tamper evident security packaging. It comes with a 2 year shelf life from date of manufacture.