Setaflash Series 8 Closed Cup Flash Point Tester-High Temperature, 82000-0

The Setaflash Series 8 is an automated closed cup flash point tester with a temperature range of ambient to 300°C (ambient to 572°F). The instrument uses an electric hot wire ignitor.

There are two modes of flash point operation; Flash/No Flash and Ramp. The ramp mode increases the sample temperature at a rate of 2°C/min, allowing determination of a flash point in accordance with ASTM D7236 and IP 534. The dipping sequence occurs automatically every 1°C up to 100°C (every 2°C rise above 100°C), until either a flash is detected or the end of test temperature is reached. The ignitor uses a new electrical hotwire (a gas flame option is available).

Methods: ASTM D3278, ASTM D3828, ASTM D7236, ASTM E502, BS 2000-523, CLP Regulations EC No 1272/2008, EPA 1020 A & B, IP 523, IP 524 (Obs), IP 534, ISO 3679, ISO 3680 (Obs), UN Class 3 Non-viscous Flammable Liquids

The bright colour LCD display shows test parameters and the flash point result. The text and colour of top line of the display indicates the instrument status. All functions are accessed via menus, navigated by the keypad. Audible prompts are given when an action is required from the operator.

The automatic flash point detection system is tuned to ignore halo and other false flash effects, reducing the chance of misinterpretation of the test result, and enhancing repeatability. Barometric pressure is measured by an internal barometer, and the correction is automatically applied to the test result. At the end of a flash point test, the sample cup is cooled by forced air to reduce the cycle time between tests. Up to 64 results can be stored in memory, tagged with operator and sample references, and can be downloaded to a PC or printer via the RS232C port. The firmware is upgradeable for future developments.

SUPPLIED WITH: Ignitor, 2ml syringe, mains lead and instruction manual.

  • Ambient to 300°C (Ambient to 572°F)
  • Small sample size, 2 or 4ml
  • Flash/No Flash & Ramp modes
  • Electric ignitor
  • Automatic dipping and flash detection
  • 64 Test memory & RS232 interface
  • °C or °F temperature display
  • Forced air cooling for rapid test cycling
Temperature Range Ambient to 300°C (Ambient to 572°F)
Sample Size 2 or 4ml according to method
Ignitor Electrical Hot Wire
Test duration, Rapid Equilibrium Mode 1 minute below 100°C, 2 minutes above 100°C,
Test duration, Ramp Mode Typically 7 minutes
Sample Cup Material Aluminium
Heating / Cooling Method Ceramic Pad, Forced Air (post-test cooldown)
Voltage 100 to 250V, 50/60Hz (2x AA dry cell batteries required for internal clock)
Power 300W (maximum)
Size (HxWxD) 30 x 34 x 38cm
Weight 8kg
CCCN Code: Tariff 90268020

Pelican™ Storm Case™ for the Setaflash Series 8, CASE-SERIES8

Sensitive equipment needs protection. This case is designed rugged and travels the harshest environments on earth. Against extreme cold or heat, Pelican cases have survived.
Made in the USA, these tough cases are designed with an automatic purge valve, that equalizes air pressure, a watertight silicone O-ring lid, over-molded rubber handles and stainless steel hardware. It is also equipped with a unique Press and Pull latch that locks automatically but opens with a light touch.

  • Six Press & Pull Latches
  • Guaranteed For Life
  • Two Padlockable Hasps
  • Two Double-layered, Soft-grip Handles
  • Two Integrated Key Lockable Latches
  • Powerful Hinges
  • O-ring seal
  • Telescoping Handle
  • Two stainless steel padlock protectors
  • Retention Strap Instructions

22.50″ x 21.10″ x 11.40″ (57.2 x 53.6 x 29 cm)
24.90″ x 23.70″ x 13.10″ (63.2 x 60.2 x 33.3 cm)
LID DEPTH: 2.00″ (5.1 cm)
BOTTOM DEPTH: 9.40″ (23.9 cm)
TOTAL DEPTH: 11.4″ (29 cm)
INT VOLUME: 3.13 ft³ (0.089 m³)
WEIGHT WITH FOAM: 24.60 lbs (11.2 kg)
WEIGHT EMPTY: 20.10 lbs (9.1 kg)
BUOYANCY: 194.16 lbs (88.1 kg)
FOAM LAYERS: Layer 1 (Lid): 2.00″ – Convolute / Layer 2 (Base): 0.63″ – Pad / Layer 3 (Base): 1.78″ – Pick N Pluck / Layer 4 (Base): 1.78″ – Pick N Pluck / Layer 5 (Base): 1.78″ – Pick N Pluck / Layer 6 (Base): 1.78″ – Pick N Pluck / Layer 7 (Base): 1.78″ – Pick N Pluck
BODY: Injection Molded HPX® high performance resin
LATCH: Valox – Polybutylene Terephthalate (PBT)
LATCH (ALT): Xenoy – Polyester/Polycarbonate blend
PINS: Stainless Steel
PINS (ALT): Aluminum
FOAM: 1.3/1.35 polyester
PURGE BODY: Valox – Polybutylene Terephthalate (PBT)
PURGE BODY (ALT): Xenoy – Polyester/Polycarbonate blend
PURGE VENT: Gortex membrane

Lazar Scientific is your reliable source for Flash Point Testing Equipment.