PM-93 Pensky-Martens Flash Point Tester, 35000-0
The Seta PM-93 is a fully automated Pensky-Martens Closed Cup Flash Point Tester which combines strict method conformance with the latest control technology and safety systems to provide the next generation of flash point instruments.
An intuitive graphic user interface and 8.4” SVGA colour touch screen operation provide unparalleled ease of use with real time display of test progress. Test profiles, operator names, test methods and storage of unlimited results are provided through the embedded operating system. Test results can be emailed, saved to a memory stick, output to LIMS or produced in hard copy with the printer option.
Methods: ASTM D93, IP 34, ISO 2719
Ignition source uses an extended life hot wire with gas option. Sample temperature probe is a class A PRT, and flash detection is by a thermocouple. Safety features include PRT checks, safety dip before starting, over-temperature cut out, gas shut off, and optional fire extinguisher. The instrument uses ‘SafeFlash’ thermally activated integral fire extinguisher (factory fit option) which discharges over the test area, it is driven by a cylinder contained within the instrument and is replaceable by the user.
Rapid turnaround between tests is achieved using a high capacity cooling fan and optimised air flow.
Calibration features include sample PRT and barometric pressure sensor with password protected access.
- NEW design, latest enhanced operation
- Fully conforms to test methods with 4 heating rates available
- Simple ‘3-step to test’ operation
- Unique patented ‘SafeFlash’ flame extinguisher system
- Large 8.4” Resistive touch screen menu
- Single action lifting arm operation
- Pre-dip safety mode
- Programmable with 30 test profiles, test methods & sample identities
- Test memory = 2000 results
- Gas or electronic ignition using proven and long lasting Seta ‘Ignite’ technology
- Compact footprint
| Ignition system: | Electric or gas |
| Flash detection: | Thermal |
| Cooling: | Forced air (integral fan) |
| Heating Rate: | Fast heating rate (>10°C/min) and standard; 5.5°C/min; 3°C/min; 1.3°C/min; 1°C/min |
| Temperature range: | Ambient +5°C to 400°C |
| Barometric pressure correction: | Automatic correction with built-in pressure sensor |
| Internal Memory: | 30 programmable test profiles, operator names, test methods and unlimited tests results |
| Fire Detection: | Thermal with optional integral Fire Extinguisher |
| Size/weight: | 38.5 x 24 x 50 cm / 25kg |
| Voltage | 230Vac +/-15% or 110Vac +/-15%. Frequency 50/60 Hz. Auto-sensing – no selector switch required. |
| CCCN Code: | Tariff 90268020 |
Pelican™ Storm Case™ for the Seta PM93, CASE-PM93
Sensitive equipment needs protection. This case is designed rugged and travels the harshest environments on earth. Against extreme cold or heat, Pelican cases have survived.
Made in the USA, these tough cases are designed with an automatic purge valve, that equalizes air pressure, a watertight silicone O-ring lid, over-molded rubber handles and stainless steel hardware. It is also equipped with a unique Press and Pull latch that locks automatically but opens with a light touch.
- Five Press & Pull Latches
- Guaranteed For Life
- Two Padlockable Hasps
- Two Double-layered, Soft-grip Handles
- Two Integrated Key Lockable Latches
- Powerful Hinges
- O-ring seal
- Two stainless steel padlock protectors
- Retention Strap Instructions
22.50″ x 21.10″ x 11.40″ (57.2 x 53.6 x 29 cm)
EXTERIOR (L X W X D)
24.90″ x 23.70″ x 13.10″ (63.2 x 60.2 x 33.3 cm)
LID DEPTH: 2.00″ (5.1 cm)
BOTTOM DEPTH: 9.40″ (23.9 cm)
TOTAL DEPTH: 11.4″ (29 cm)
INT VOLUME: 3.13 ft³ (0.089 m³)
WEIGHT WITH FOAM: 24.60 lbs (11.2 kg)
WEIGHT EMPTY: 20.10 lbs (9.1 kg)
BUOYANCY: 194.16 lbs (88.1 kg)
FOAM LAYERS: Layer 1 (Lid): 2.00″ – Convolute / Layer 2 (Base): 0.63″ – Pad / Layer 3 (Base): 1.78″ – Pick N Pluck / Layer 4 (Base): 1.78″ – Pick N Pluck / Layer 5 (Base): 1.78″ – Pick N Pluck / Layer 6 (Base): 1.78″ – Pick N Pluck / Layer 7 (Base): 1.78″ – Pick N Pluck
BODY: Injection Molded HPX® high performance resin
LATCH: Valox – Polybutylene Terephthalate (PBT)
LATCH (ALT): Xenoy – Polyester/Polycarbonate blend
O-RING: EPDM
PINS: Stainless Steel
PINS (ALT): Aluminum
FOAM: 1.3/1.35 polyester
PURGE BODY: Valox – Polybutylene Terephthalate (PBT)
PURGE BODY (ALT): Xenoy – Polyester/Polycarbonate blend
PURGE VENT: Gortex membrane
MINIMUM TEMPERATURE: -20° F (-29 ° C)
MAXIMUM TEMPERATURE: 140° F (60 ° C)
CERTIFICATIONS: MIL-STD-810F / ATA 300 / FED-STD-101C
EXTENDABLE HANDLE: yes
PM93 Hardcase
Air Pressure Release Valve
